ON Semiconductor

Operating Input Voltage Range: 2.5V to 5.5V; High Ripple Rejection Ratio: Typ. 82dB @ 1kHz; Ultra-Low Output Noise: Typ. 10µVrms from 10Hz to 100kHz; Stable with output capacitors as low as 1µF; Active Discharge; Output Voltage Options: 1.8V, 2.8V, 3.0V, 3.3V; Low Sleep Mode Current: Max. 1A; Current Limit Protection; Thermal Shutdown Protection; Output Current Limit: Min. 200mA; No-Load Ground Current of Typ. 70µA; Full-Load Ground Current of Typ. 75µA; Output voltage accuracy: ±2.5% over Load/Line Regulat

Low Quiescent Current Sleep Mode; HighSide and LowSide Drivers Connected in a HalfBridge Configuration; Integrated Freewheeling Protection (LS and HS); 0.55 A Peak Current; RDS(on) = 1 ohm (typ); Overcurrent Protection; Overtemperature Protection; Under Load Detection; Discriminated Fault Reporting; 16Bit Frame Detection; Daisy Chain Compatible with Multiple of 8 bit Devices; 5 MHz SPI Control; Compliance with 5 V and 3. 3 V Systems; Undervoltage and Overvoltage Lockout

SOIC-28

High Speed (up to 1 Mbps); Compatible with the ISO 11898−2 Standard; VIO Pin on NCV7351D13 Version Allowing Direct Interfacing with 3V to 5V Microcontrollers; EN Pin on NCV7351D1E Version Allowing Switching the transceiver to a Very Low Current OFF Mode; Excellent Electromagnetic Susceptibility (EMS) Level Over Full Frequency Range. Very Low Electromagnetic Emissions (EME) Low EME also Without Common Mode (CM) Choke; Bus Pins Protected Against >15 kV System ESD Pulses; Transmit Data (TxD) Dominant Time−out

High Speed (up to 1 Mbps); Compatible with the ISO 11898−2 Standard; VIO Pin on NCV7351D13 Version Allowing Direct Interfacing with 3V to 5V Microcontrollers; EN Pin on NCV7351D1E Version Allowing Switching the transceiver to a Very Low Current OFF Mode; Excellent Electromagnetic Susceptibility (EMS) Level Over Full Frequency Range. Very Low Electromagnetic Emissions (EME) Low EME also Without Common Mode (CM) Choke; Bus Pins Protected Against >15 kV System ESD Pulses; Transmit Data (TxD) Dominant Time−out

Low Electromagnetic Emission (EME) and Extremely High Electromagnetic Immunity; Compatible with the ISO 11898−5 Standard; High Speed (up to 1 Mbps); No Disturbance of the Bus Lines with an Un−powered Node; Transmit Data (TxD) Dominant Time−out Function; Very Low Current Standby Mode with Wake−up via the Bus; Very Low EME without Common−mode (CM) Choke; Under All Supply Conditions the Chip Behaves Predictably; Very High ESD Robustness of Bus Pins, >10 kV System ESD Pulses; Thermal Protection; Bus Pins Short

SOIC-14

UltraFast Transient Response (Settling Time: 1 - 3 us); Low Noise Without Bypass Capacitor (26 uVrms); Low Ground Current Independent of Load (3.0 mA Maximum); Fixed/Adjustable Output Voltage Versions; Enable Function; Error Flag (Fixed Output Version); Current Limit Protection; Thermal Shutdown Protection (160C); 0.9 V Reference Voltage for Ultra-Low Output Operation; Power Supply Rejection Ratio > 65 dB

Integrated 1.5 A Switch ; Input Voltage Range from 3 V to 40 V ; Low Feedback Voltage of 235 mV ; Cycle-by-Cycle Current Limit; No Control Loop Compensation Required ; Frequency of Operation Adjustable up to 250 kHz; Operation With All Ceramic Output Capacitors or No Output Capacitance ; Analog and Digital PWM Dimming Capability; Internal Thermal Shutdown with Hysteresis

Oscillator Frequency Guaranteed at 250 kHz; Current Mode Operation to 500 kHz; Automatic Feed Forward Compensation; Latching PWM for Cycle−By−Cycle Current Limiting; Internally Trimmed Reference with Under-voltage Lockout; High Current Totem Pole Output; Under-voltage Lockout with Hysteresis; Low Startup and Operating Current; These are Pb−Free Devices; Trimmed Oscillator for Precise Frequency Control

Internal Thermal Overload Protection; Output Current in Excess of 100 mA; Output Transistor Safe-Area Compensation; Internal Short Circuit Current Limiting; Standard 3-Lead Transistor Package; Eliminates Stocking Many Fixed Voltages; Output Adjustable Between 1.2 V and 37 V; Floating Operation for High Voltage Applications; Pb-Free Packages are Available; NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes

Low Input Offset Current: 5.0 nA; Low Input Offset Voltage: 2.0 mV (max) LM393A 5.0 mV (max) LM293/393; Low Input Bias Current: 25 nA; Wide Single-Supply Range: 2.0 Vdc to 36 Vdc; Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS Logic Levels; ESD Clamps on the Inputs Increase the Ruggedness of the Device without Affecting Performance; Input Common Mode Range to Ground Level; Very Low Current Drain Independent of Supply Voltage: 0.4 mA; Split-Supply Range: +/-1.0 Vdc to +/-18 Vdc; Differential Inp

Short Circuit Protected Outputs; Low Input Bias Currents; Single Supply Operation: 3.0 V to 32 V ; Single and Split Supply Operation; Internally Compensated; ESD Clamps on the Inputs Increase Ruggedness of the Device without Affecting Operation; True Differential Input Stage; Common Mode Range Extends to Negative Supply; Pb-Free Packages are Available

Operation up to 40 V Input; Frequency operation up to 150 KHz; Internal thermal Shutdown with hysteresis; Cycle-by-Cycle Current Limiting; Excel Based Design Tool; Adjustable current limit

Use the download button to access the NCV4949APDR2G schematic symbol, PCB footprint, and 3D model.

Use the download button to access the NCV5501DT50RKG schematic symbol, PCB footprint, and 3D model.

Operation up to 40 V Input; Frequency operation up to 150 kHz (250 kHz if used as a controller); Internal thermal Shutdown with hysteresis; Cycle-by-Cycle Current Limiting; Low power standby mode (<100µA)

Low Quiescent Current of 2.8 µA Typical; Low Output Voltage Option; Output Voltage Accuracy of 2.0%; Industrial Temperature Range of –40°C to 85°C; NCP552 Provides an Enable Pin; Pb-Free Packages are Available*

Power Bandwidth: 160 kHz; Unity Gain Stable: w/Capacitance Loads to 500 pF; ESD Diodes Provide Added Protection to the Inputs; Input Offset Voltage Trimmed to 100 µV (Typ); Low Noise: 18 nV/ (sq. root Hz) @ 1.0 kHz; Low Input Bias Current: 300 nA; Single or Split Supply Operation: +3.0 V to +36 V or +/-1.5 V to +/-18 V; Excellent Frequency Stability; Large Output Voltage Swing: +14.1 V/ -14.6 V; Low Total Harmonic Distortion: 0.003%; Low Input Offset Current: 3.0 nA; High Slew Rate: 10 V/µs; High Input Resi

Output Current in Excess of 800 mA; 1.0 V Dropout; Short Circuit Protection; Output Trimmed to 1.0% Tolerance; Thermal Protection; 3.3 V, 5.0 V, 12 V and Adjustable Versions 2.85 V version available as MC34268.; Space Saving DPAK, SOP-8 and SOT-223 Power Packages; Pb-Free Packages are Available

5.0V and 3.3V +/- 2% Output with 150mA Output Current Capability; Active Reset Output Low Down to VQ=1.0V; Adjustable Reset Threshold; Fault Protection: -40V Reverse Voltage Protection Short Circuit Protection Thermal overload protection; Early Warning through SI/SO Leads, adjustable threshold via external resistor; Very Low Dropout Voltage; AEC Q100 Qualified; Integrated Pullup Resistor at Logic Outputs (To Use External Resistors, Select the NCV4279A)

Use the download button to access the NCP803SN463T1G schematic symbol, PCB footprint, and 3D model.

Low Input Offset Current: 5.0 nA; Low Input Offset Voltage: 2.0 mV (max) LM393A 5.0 mV (max) LM293/393; Low Input Bias Current: 25 nA; Wide Single-Supply Range: 2.0 Vdc to 36 Vdc; Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS Logic Levels; ESD Clamps on the Inputs Increase the Ruggedness of the Device without Affecting Performance; Input Common Mode Range to Ground Level; Very Low Current Drain Independent of Supply Voltage: 0.4 mA; Split-Supply Range: +/-1.0 Vdc to +/-18 Vdc; Differential Inp

Comparator, Dual, Variable-Reluctance Sensor Interface

Output Current in Excess of 1.0 A; 1.2 V Maximum Dropout Voltage at 800 mA Over Temperature; Fixed Output Voltages of 1.5 V, 1.8 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V; Adjustable Output Voltage Option; No Minimum Load Requirement for Fixed Voltage Output Devices; Reference/Output Voltage Trimmed to +/- 1.0%; Current Limit, Safe Operating and Thermal Shutdown Protection; Operation to 20 V Input; Pb-Free Packages are Available

Output Current in Excess of 1.0 A; 1.2 V Maximum Dropout Voltage at 800 mA Over Temperature; Fixed Output Voltages of 1.5 V, 1.8 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V; Adjustable Output Voltage Option; No Minimum Load Requirement for Fixed Voltage Output Devices; Reference/Output Voltage Trimmed to +/- 1.0%; Current Limit, Safe Operating and Thermal Shutdown Protection; Operation to 20 V Input; Pb-Free Packages are Available

On-Chip and Remote Temperature Sensor; 0.25°C Resolution/1°C Accuracy on Remote Channel; 1°C Resolution/1°C Accuracy on Local Channel; Series Resistance Cancellation up to 1.5 kΩ; Extended, Switchable Temperature Measurement Range 0°C to +127°C (Default) or -64°C to +191°C; Pin and Register Compatible with NCT1008; Remote /THERM limit of 108°C; 2-Wire SMBus/I2C Serial Interface with SMBus Alert Support; Programmable Over/Undertemperature Limits; Offset Registers for System Calibration; Up to Two Overtempera

Low Voltage, Single Supply Operation (1.8 V and Ground to 10 V and Ground); 1.0 pA Input Bias Current; Unity Gain Bandwidth of 1.0 MHz at 5.0 V, 0.9 MHz at 1.8 V; Output Voltage Swings Within 50 mV of Both Rails @ 1.8 V; No Phase Reversal on the Output for Over-Driven Input Signals; Input Offset Trimmed to 1.0 mV; Low Supply Current (ID = 1.0 mA); Works Down to Two Discharged NiCd Battery Cells; ESD Protected Inputs Up to 2.0 kV

Three 6th Order Standard Definition 8 MHz Filters; Internal Fixed Gain = 6 dB; AC- or DC- Coupled Inputs / Outputs; Integrated Level Shifter; Operating Voltage +5 V; ESD HBM Protection > 8 kV

Differential Output; 1.0 W into an 8 Speaker; 1.5 W into a 4 Speaker; Single Supply Operation: 2.7 V to 5.5 V; THD+N: 0.2% @ 1 W Output; Low Quiescent Current: 20 mA Max; Shutdown Current < 1.0 A; Excellent Power Supply Rejection; Two Package Options: SOIC-8 Package and DFN8; Pin Compatible with Competitive Devices; Notebook Computing

Operating Voltage of 0.85 V to 6.0 V; Rail-to-rail Input/Output Performance; Low Supply Current of 10 µA; No Phase Inversion/Glitchless transitioning in or out of Tri-State Mode; Complementary or Open Drain Output Configuration; Available with the Enable Function

Operating Voltage of 0.85 V to 6.0 V; Rail-to-rail Input/Output Performance; Low Supply Current of 10 µA; No Phase Inversion/Glitchless transitioning in or out of Tri-State Mode; Complementary or Open Drain Output Configuration; Available with the Enable Function

Operating Voltage of 0.85 V to 6.0 V; Rail-to-rail Input/Output Performance; Low Supply Current of 10 µA; No Phase Inversion/Glitchless transitioning in or out of Tri-State Mode; Complementary or Open Drain Output Configuration; Available with the Enable Function

Operating Voltage of 0.85 V to 6.0 V; Rail-to-rail Input/Output Performance; Low Supply Current of 10 µA; No Phase Inversion/Glitchless transitioning in or out of Tri-State Mode; Complementary or Open Drain Output Configuration; Available with the Enable Function

Operating Voltage of 0.85 V to 6.0 V; Rail-to-rail Input/Output Performance; Low Supply Current of 10 µA; No Phase Inversion/Glitchless transitioning in or out of Tri-State Mode; Complementary or Open Drain Output Configuration; Available with the Enable Function

7 MHz Unity Gain Bandwidth at 5 V; 5 MHz Unity Gain Bandwidth at 1.8 V; Rail-to-Rail Output; No Output Phase Reversal for Over-Driven Input Signals; Low Offset Voltage - 500 µV typical; Low Input Bias Current - 1 pA typical; SOT23-5 and SOT553-5 Packages; 8V/us Slew Rate at 5V; NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable

Use the download button to access the NCP803SN400T1G schematic symbol, PCB footprint, and 3D model.

ON Semiconductor NCP803SN293D3T1G, Voltage Supervisor 3.08V max. N 3-Pin, SOT-23

Operating Input Voltage Range: 2.0V to 5.5V; Ultra-Low Output Noise: Typ. 11µVrms from 100Hz to 100kHz; Ultra-Low No-Load Ground Current of Typ. 10µA; Adaptive Ground Current Feature; High Ripple Rejection Ratio: Typ. 70dB @ 1kHz; Stable with small 1µF ceramic output capacitor; Guaranteed Min. Output Current: 200mA; Available Fixed Output Voltage Options: 0.8V to 3.5V; Output voltage trimming step: 2.5mV; Enable/Shutdown Pin Function; Ultra-Low Shutdown Mode Current: Max. 1µA; Active Output Discharge; Ouput

Operating Input Voltage: 2.5V to 5.5V; Output Voltage Options: 1.8V, 2.8V, 3.0V, 3.3V; High Ripple Rejection Ratio: Typ. 82dB @ 1kHz; Ultra-Low Output Noise: Typ. 10µV from 10Hz to 100kHz; Stable with output capacitors as low as 1uF ; Low Sleep Mode Current: Max. 1µA; Active Discharge; Current Limit Protection; Thermal Shutdown Protection; These are Pb-Free Devices; Output Current Limit: Min. 200mA; No-Load Ground Current of Typ. 70µA ; Full-Load Ground Current of Typ. 75µA ; Output voltage accuracy: ±2.5%

LEAD FREE, SC-82AB, SC-70, 4 PIN

LEAD FREE, SOT-89, 5 PIN

ON Semiconductor NCP692MN18T2G, LDO Voltage Regulator, 1A, 1.8 V ±2%, 1.5 → 6 Vin, 6-Pin DFN

2.3 V to 5.5 V Input Voltage Range; External Adjustable Voltage; Specific Fixed Voltage in Range of 0.6 V to 3.3 V is Available upon Request; Up to 2 A Output Current; 3 MHz Switching Frequency (1.5 MHz Version is Available upon Request); Synchronous Rectification; Enable Input; Power Good Output; Soft Start; Over Current Protection; Active Discharge when Disabled. HiZ version available upon request; Thermal Shutdown Protection; WDFN8, 2x2 mm, 0.5 mm Pitch Package; Maximum 0.8 mm Height for Super Thin Appli

Last Shipments - Linear Voltage Regulator, 3 A, Ultra-High PSRR

LDO Regulator, 150 mA, High PSRR, Low Noise, with On/Off Control Vout: 5.0 V

Output Voltage Options:Adjustable, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V; Adjustable Output by External Resistors from 5.0 V down to 1.25 V; Current Limit 675 mA; Low IGND (Independent of Load); ±1.5% Output Voltage Tolerance Over All Operating Conditions(Adjustable); ±2% Output Voltage Tolerance Over All Operating Conditions(Fixed); NCP605 Fixed is Direct Replacement LP8345; Typical Noise Voltage of 50 µVrms without a Bypass Capacitor; Enhanced ESD Ratings: 4 kV Human Body Mode (HBM) 400 V Machin

DFN-6

Output Current in excess of 3 Amps; 175 mV typical dropout at 1.5 A output and 300 mV typical dropout at the full 3.0 A load.; Low Ground current - 60 mA typical at 3 Amp load; Stable with ceramic capacitors on the output; NCV version available for Automotive applications; Maximum voltage input 18V; Error flag available on the NC59301 option

ON Semiconductor NCP59152MNADJTYG, LDO Voltage Regulator, Adjustable 1.5A, ±2%, 2.24 → 13.5 Vin, 8-Pin DFN