Microchip

IC, 8BIT CMOS MCU

Microchip MCP603-I/P is a single rail-to-rail operational amplifier with 75 dB minimum CMRR, 60 pA maximum bias current, and frequency compensation in an 8-pin PDIP package. Available from stock with worldwide shipping.

Rail-to-Rail Op Amp

8-Bit CMOS Microcontrollers

Microchip MCP25050-E/P is an 8-bit CAN I/O expander in a 14-pin DIP package, providing SPI-to-CAN bridging with GPIO expansion for embedded control nodes requiring network-based digital I/O management in automotive and industrial systems.

MCP6285-E/P is a 8 pins amplifier by Microchip. Key specs: 8 pins, Dual-In-Line Packages package, Rail-to-Rail Op Amp. From quote-based sourcing, in stock checks support worldwide shipping.

8-bit real time clock/counter (TMR0) with 8-bit programmable prescaler • Power-On Reset (POR) • Device Reset Timer (DRT) • Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation • Programmable code-protection • 1,000,000 erase/write cycle EEPROM data memory • EEPROM data retention > 40 years • Power saving SLEEP mode • Wake-up from SLEEP on pin change • Internal weak pull-ups on I/O pins • Internal pull-up on MCLR pin • Selectable oscillator options: - INTRC: Internal

MCP6S92-E/P is a 2-channel programmable gain amplifier (PGA) from Microchip with selectable gain settings and SPI interface. Features single-supply operation from 2.5 V to 5.5 V with low offset voltage. Available from stock worldwide with fast shipping.

Rail-to-Rail Op Amp

16-Bit Digital Signal Controllers

Digital POT

In-Circuit Serial Programming (ICSP™) • Internal 4 MHz oscillator with programmable calibration • Selectable clockout • Power-on Reset (POR) • Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) • Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation • Programmable code protection • Power saving SLEEP mode • Interrupt-on-pin change (GP0, GP1, GP3) • Internal pull-ups on I/O pins (GP0, GP1, GP3) • Internal pull-up on MCLR pin • Selectable oscillator options: - INT

IC, IRDA CTRL, 115.2KBAUD

DSPIC33FJ64MC710 is a 16-bit digital signal controller with 64 KB Flash, running at up to 64 MHz with a fixed-point DSP engine and hardware barrel shifter. It operates from a 3.3 V supply, features motor control PWM and multiple internal bus architecture, and includes JTAG boundary scan. Packaged in a 100-pin TQFP for motor control and embedded digital signal processing applications.

Microchip MCP4141 is a single-channel 7-bit non-volatile digital potentiometer with 50 kOhm resistance and increment/decrement control in an 8-pin PDIP package. It offers 128-step resolution with EEPROM wiper memory. Available in stock worldwide with fast worldwide shipping.

MCP73861-I/MLG is a Microchip integrated circuit for PCB-level interconnects, replacement sourcing, or production BOMs. Key specs include 16 pins, -40°C to 85°C operating range, SMD/SMT. From inquiry pricing, in stock sourcing, and worldwide shipping support.

Microchip MCP4142-104E/P is a single-channel 7-bit digital potentiometer with 100 kΩ end-to-end resistance and an SPI-compatible increment/decrement interface. It provides 128 resistance steps in an 8-pin PDIP package, suitable for gain control, offset adjustment, and programmable biasing in analog signal conditioning circuits.

Microchip MCP73863-I/ML is a single-channel linear Li-Ion battery charger IC with integrated safety features, housed in a compact 4x4 mm 16-pin QFN package for portable and handheld battery-powered device applications.

MCP6544-E/P is a 14 pins integrated circuit by Microchip. Key specs: 14 pins, Dual-In-Line Packages package, Push-Pull Output Sub-Microamp Comparators. From quote-based sourcing, in stock checks support worldwide shipping.

MCP6275-E/P is a 8 pins amplifier by Microchip. Key specs: 8 pins, Dual-In-Line Packages package, Standard Amplifier 2 Circuit Rail-to-Rail 8-PDIP. From quote-based sourcing, in stock checks support worldwide shipping.

DSC, 16BIT 128KB 40MHZ 3.6V

MCP4011-503E/MS is a single-channel 50 kΩ volatile digital potentiometer by Microchip, controlled via a 2-wire Up/Down interface in an MSOP-8 package. Features 64 wiper positions with 0.2 kHz bandwidth and 5V operation. Ideal for calibration and gain adjustment circuits. From $0.85, in stock, worldwide shipping.

The MCP619-I/P is a quad operational amplifier from Microchip featuring a PNP input stage that operates from a 2.3 V single supply. It provides 100 dB typical CMRR, 5 nA maximum input bias current, and rail-to-rail output capability in a 14-pin DIP package for portable and battery-powered signal conditioning.

MCP201-I/P is a single-channel voltage supervisor IC from Microchip in an 8-pin DIP package, providing precise undervoltage reset detection for 3.3 V and 5 V microcontroller systems. It asserts an active-low RESET signal during power-up and brownout events. Available in RoHS-compliant PDIP-8 with worldwide distribution.

Microchip MCP2155-I/P is an infrared encoder/decoder IC in an 18-pin DIP package, supporting SIR-compatible IrDA transmit and receive up to 115.2 kbps. Compact single-function design enables low-cost IR communication in embedded systems with worldwide shipping.

Microchip MCP42050-E/P is a dual-channel 8-bit digital potentiometer with SPI interface providing 50 kΩ end-to-end resistance and 256 wiper positions per channel. Operating from 2.7 V to 5.5 V supply with 3-wire serial control in a 14-pin PDIP package. Available from stock with worldwide shipping for volume orders.

93LC46A/P is a 1 Kbit Microwire-compatible serial EEPROM from Microchip in an 8-pin PDIP package. It supports up to 2 MHz clock, 1 million write/erase cycles, and 200-year data retention for reliable embedded configuration storage.

Microchip MCP2140-I/SO is an IrDA infrared communications controller operating up to 5.5 V supply, housed in an 18-pin SOIC package, providing full IrDA physical layer protocol support for wireless serial data transfer in portable and consumer electronics devices.

Microchip MCP4231-503E/P is a dual-channel SPI digital potentiometer with 50 kΩ end-to-end resistance and 256 wiper positions. Features increment/decrement control interface and wide 1.8 V to 5.5 V operating range. Available from stock worldwide with fast shipping.

The MCP131-450E/TO is a single-channel voltage supervisor and microcontroller reset IC from Microchip, with a fixed threshold of 4.38 V. It monitors supply voltage and asserts a reset output when VCC falls below the threshold, ensuring reliable system startup and brownout protection. Available in the compact TO-92-3 through-hole package from global authorized distributors.

DSPIC30F2011-20I/P is a 16-bit digital signal controller from Microchip with a 40 MHz DSP core, hardware barrel shifter, and fixed-point arithmetic in an 18-pin PDIP package. Available from stock with worldwide shipping.

MCP1318MT-46LE/OT is a single-channel Voltage Supervisor and Reset IC in SOT-23-5 package from Microchip. Features a fixed 4.6 V detection threshold with no external components needed for reliable power-on and brownout reset supervision. Available from stock with worldwide shipping.

Microchip MCP130-475FI/TO is a single-channel voltage supervisor and microcontroller reset IC with a 4.75 V trip threshold and an internal 5 kOhm pull-up resistor in a TO-92-3 through-hole package. It holds the reset output low when VCC falls below 4.75 V to ensure clean microcontroller startup and brownout protection. Available from stock worldwide with fast shipping.

Microchip MCP4141-502E/P is a single-channel, 7-bit SPI digital potentiometer with 5 kΩ end-to-end resistance, operating from 1.8 V to 5.5 V, ideal for audio, instrumentation, and calibration circuits.

Microchip dsPIC33FJ64MC508 is a 16-bit digital signal controller with 64 KB Flash, 8 KB RAM, and a 40 MIPS performance core. Features motor control PWM, QEI, and 12-bit ADC. Available from stock with worldwide shipping.

Microchip 93AA46AT-I/OT is a 1K-bit Microwire-compatible serial EEPROM in a compact SOT-23-6 package operating at up to 3 MHz clock. Offers 1 million write/erase cycles and 200-year data retention for reliable non-volatile storage. RoHS compliant and available in tape and reel for automated PCB assembly.

Microchip MCP2140A-I/P is an IrDA Standard Controller supporting DTE and DCE modes in an 18-pin DIP package. It features integrated IR encoder/decoder with baud rates up to 115.2 kbps. Available from stock worldwide with competitive pricing.

MCP1825-1802E/AT is a fixed 1.8 V, 500 mA LDO linear voltage regulator from Microchip featuring ultra-low 210 mV typical dropout voltage and 6 V maximum input. Designed for portable and embedded systems, it provides stable power with fast transient response and only 120 µA quiescent current. Available in a compact TO-220-5 package for easy integration into space-constrained designs.

Microchip dsPIC33FJ256MC710-I/PF is a 16-bit digital signal controller with 256 KB flash, 64 MHz maximum clock, and motor control peripherals in a 100-pin TQFP package. It integrates DSP fixed-point math, barrel shifter, and boundary scan for advanced embedded motor control. Available in stock with worldwide shipping.

16-Bit Digital Signal Controllers

The MCP103T-475E/TT is a micropower single-channel voltage supervisor from Microchip with a fixed threshold and SOT-23-3 packaging. It monitors supply voltages and generates a reset signal to protect microcontrollers during power-up or brownout events. From $0.35, in stock worldwide shipping.

The DSPIC33FJ64GP710-I/PT is a 16-bit digital signal controller from Microchip, running at up to 64 MHz with 64 KB Flash, fixed-point DSP engine, DMA channels, and ADC. It is offered in a 100-pin TQFP package for motor control and power conversion designs worldwide.

The MCP131-300E/TO is a single-channel voltage supervisor and microcontroller reset IC from Microchip with a fixed 2.93 V threshold, active-low reset output, and single-supply operation. Housed in a 3-pin TO-92 through-hole package for cost-effective system protection. From $0.50 in stock with worldwide shipping.

Microchip DSPIC30F2010-20I/SO is a 16-bit digital signal controller in a 28-pin SOIC package. It runs at up to 40 MHz clock frequency with a built-in ADC and barrel shifter for real-time motor control. Available from stock with worldwide shipping.

Microchip MCP1601-I/MS is a voltage-mode PWM switching regulator with 2.7 V to 5.5 V input range supporting PFM operation. Delivers regulated DC output in a compact MSOP-8 package with high efficiency for battery-powered applications. RoHS-compliant and available with worldwide shipping.

2K Microwire Compatible Serial EEPROM

The MCP101-315HI/TO is a single-channel microcontroller voltage supervisor and reset IC by Microchip, with a fixed 3.15 V threshold, 45 µA supply current, and 5.5 V maximum supply. Housed in a TO-92-3 through-hole package, it provides reliable power-on reset generation for microcontrollers and digital systems requiring voltage monitoring.

The HCS360-I/SN is a Microchip KEELOQ code hopping encoder IC delivering rolling-code security for remote keyless entry and access control systems. It generates a 66-bit encrypted transmission with a unique 64-bit serial number and operates in an 8-pin SOIC package rated for 260°C peak reflow. Available from stock worldwide with competitive pricing.

The DSPIC30F6013-20I/PF is a 16-bit digital signal controller from Microchip with a 40 MHz clock, fixed-point DSP engine, barrel shifter, and 80-pin TQFP package. It operates down to 2.5 V at 7.5 MHz, combining MCU peripherals with DSP processing for embedded control.

1K Microwire Compatible Serial EEPROM