Microchip

The MCP9801-M/SN is a high-accuracy 12-bit digital temperature sensor from Microchip with a 2-wire I2C serial interface. It measures temperature with up to ±1°C accuracy in typical conditions and a maximum error of ±3°C, packaged in an SOIC-8. Ideal for thermal management, overcurrent detection, and environmental monitoring in industrial and consumer systems.

Microchip MCP9843-BE/ST is a JEDEC-compliant I2C serial temperature sensor with ±2°C maximum accuracy and B-grade temperature range. The 4.4 × 3 mm TSSOP-8 plastic package provides a compact, digitally readable thermal solution for system thermal management and environmental monitoring.

Microchip MCP9805-BE/ST is a JC42.4-compliant I2C digital temperature sensor with ±3 °C accuracy, programmable alert thresholds, and 12-bit resolution in a TSSOP-8 package. It operates from 3.0 V to 3.6 V for JEDEC DDR memory thermal monitoring. Available with worldwide shipping.

Temperature Sensor 12bit I2C SOT23-5

Microchip MCP9509HT-E/OT is a resistor-programmable temperature switch with open-drain output, trip-point accuracy of ±2°C, and supply range from 2.7 V to 5.5 V, housed in a 5-pin SOT-23 package for board-level thermal protection.

The MCP810T-475I/TT is a microprocessor supervisor IC from Microchip that monitors a 4.625 V threshold and asserts a reset signal when supply voltage drops below this level. Fixed threshold in a 3-pin SOT-23 package enables simple, low-cost system reset protection. Available from stock worldwide.

The MCP9510CT-E/CH is a digital temperature sensor and fan controller IC in a compact SOT-23-6 package from Microchip. It monitors temperature and controls cooling fans with programmable thresholds and alert outputs. Available with worldwide shipping for thermal management applications.

The MCP9509CT-E/OT is a resistor-programmable temperature switch IC that sets its trip threshold via an external resistor, delivering a digital output when the ambient temperature crosses the programmed limit. It integrates threshold detection without an MCU in a compact 5-pin SOT-23 package with matte tin finish. Available from stock with RoHS-compliant construction and worldwide shipping.

The MCP809T-460I/TT is a single-channel voltage supervisor IC from Microchip with a fixed 4.60 V reset threshold and push-pull active-low output in a 3-pin SOT-23 package. It monitors system supply rails and holds the microprocessor in reset until voltage rises above the threshold. Designed for reliable power-on reset management in consumer, industrial, and embedded control applications.

Microchip MCP810T-315I/TT is a single-channel voltage supervisor with a fixed 3.075 V active-high reset threshold, internal 140 ms timeout delay, and push-pull output, in a 3-pin SOT-23 package for microcontroller power-on reset.

Microchip MCP79410-I/MS is an I2C real-time clock and calendar IC featuring 1 Kb EEPROM, 64 bytes SRAM, and a unique ID register in an MSOP-8 package. It operates from 1.8 V with 100 kHz I2C and provides interrupt output for alarm-driven wake-up. Available with worldwide shipping.

MCP809T-300I/TT is a single-channel microprocessor supervisor and reset IC from Microchip with a fixed 2.925 V threshold voltage. It asserts an active-low reset output whenever the monitored supply falls below 2.925 V, ensuring controlled startup and brownout protection. Supplied in a tiny 3-pin SOT-23 package for space-critical embedded and IoT applications.

MCP809T-315I/TT is a microprocessor supervisory reset IC from Microchip with a fixed 3.15 V threshold and active-low push-pull reset output. It requires no external components and monitors supply voltage in a tiny 3-pin SOT-23 package with ultra-low quiescent current.

uP supervisor IC,MCP809T-450I/TT 4.375V

The MCP809T-475I/TT is a single-channel voltage supervisor and microprocessor reset IC from Microchip with a fixed 4.75 V threshold in a tiny SOT-23 3-pin package. It monitors supply voltage and asserts a reset signal when the rail falls below the programmed level. Ideal for microcontroller reset management in consumer, industrial, and automotive embedded systems.

Microchip MCP73855-I/MF is a single-channel linear battery charger IC in a compact 3 mm × 3 mm, 0.9 mm height 10-pin DFN package, designed for single-cell Li-ion and Li-polymer battery charging applications. It provides a complete constant-current/constant-voltage charge algorithm without an adjustable threshold in a Pb-free, RoHS-compliant form factor. Available from stock with worldwide shipping.

The MCP6V03-E/SN is a single-channel auto-zero operational amplifier from Microchip featuring a maximum input offset voltage of 2 µV and a CMRR of 142 dB typical. It includes an integrated chopper-stabilization circuit and operates from 1.8 V to 5.5 V single supply, housed in an 8-pin SOIC package. Ideal for precision DC measurement, strain gauge, and low-level sensor amplification.

Li-Ion Charger USB/DC 4.5V 1A PG DFN10

The MCP73838-NVI/MF is a single-cell linear Li-Ion and Li-Polymer battery charger controller from Microchip featuring adjustable charge termination thresholds and charge current. It integrates charge status outputs and thermal regulation in a compact 10-pin DFN package, making it ideal for USB-powered portable devices requiring safe and precise single-cell battery management.

The MCP79410-I/ST is a real-time clock IC with I2C interface, 32.768 kHz oscillator, and 64-byte SRAM for battery-backed timekeeping in embedded systems. It operates from 1.8V nominal with I2C speeds up to 400 kHz (100 kHz at 1.8V) and supports interrupt output for alarm events. Housed in an 8-pin TSSOP package for compact timekeeping designs in consumer and industrial electronics.

MCP809T-270I/TT is a single-channel voltage supervisor and microcontroller reset IC from Microchip with a fixed 2.625 V threshold and active-low open-drain output. It monitors supply rails with a 140 ms minimum reset assertion time, housed in a 3-pin SOT-23 package for space-constrained 2.5 V to 3.3 V system reset and brownout-protection applications.

The MCP73114-0NSI/MF is a single-cell lithium-ion/lithium-polymer battery charger IC from Microchip Technology, featuring 5.8V overvoltage protection, programmable charge current up to 500 mA, and a DFN-10 package. Ideal for portable consumer electronics and USB-powered devices.

The MCP73864-I/SL is a dual-channel linear battery charger IC by Microchip in a 16-pin SOIC package, designed for Li-Ion and Li-Polymer cell charging with fixed threshold control and RoHS-compliant lead-free construction. Supports 2 independent charge channels for multi-cell portable designs. Available from authorized distributors with worldwide shipping.

The MCP4132-503E/SN is a single-channel 7-bit digital potentiometer from Microchip with 128 resistance steps and a 50 kohm end-to-end resistance. It uses an increment/decrement control interface and is housed in an SOIC-8 package. Suitable for programmable gain, offset, and calibration circuits in industrial and consumer electronics.

The MCP73837-FJI/MF is a single-cell Li-Ion and Li-Polymer linear battery charger IC from Microchip with adjustable charge current threshold. It provides complete constant-current/constant-voltage charge management in a compact 10-lead DFN package. Available from stock worldwide with competitive pricing.

0.150 INCH, LEAD FREE, PLASTIC, MS-012, SOIC-16

Li-Ion Charger USB/DC 4.5V 1A TE DFN10

Microchip MCP73861-I/SL is a linear lithium-ion and lithium-polymer battery charger IC supporting up to 1 A charge current with integrated preconditioning and end-of-charge detection in a 16-pin SOIC package. Provides charge status outputs, thermal regulation, and safety timer in a fully integrated solution requiring minimal external components. Available from stock with worldwide shipping.

Microchip MCP73838T-FCI/MF is a linear Li-Ion/Li-Polymer battery charger IC supporting USB and DC input, up to 1 A charge current, and a 4.2 V regulated charge voltage. Features thermal regulation, programmable charge current via resistor, and LED charge-status outputs in a 10-pin DFN package. Available from stock with worldwide shipping.

Microchip MCP4562-502E/MS is a single-channel I2C digital potentiometer with 256 steps and 5 kOhm end-to-end resistance featuring non-volatile EEPROM wiper memory in an MSOP-8 package. Available from stock with worldwide shipping.

The MCP73853-I/ML is a single-cell Li-Ion linear battery charge controller with USB temperature sensing from Microchip Technology. It supports a single charge channel in a 16-pin VQFN package and complies with USB charging standards. Ideal for portable consumer devices, wearables, and USB-powered battery backup systems requiring compact, safe Li-Ion charging.

The MCP6G01-E/SN is a single-channel instrumentation amplifier gain block from Microchip operating from 1.8 V with 0.9 MHz bandwidth, 5 nA maximum bias current, and 4.5 mV maximum input offset voltage in an 8-pin SOIC package. It provides fixed programmable gain suitable for low-power sensor amplification and signal conditioning. Available from global distributors with worldwide shipping.

The MCP73844-840I/MS is a single-cell Li-Ion charge controller with an 8.4 V regulation voltage targeting 2-cell series battery packs. It includes an adjustable threshold monitor and drives an external pass FET for flexible current control. Available in an MSOP-8 package with worldwide shipping.

Li-Ion/Li-Po Batt Ctrlr,MCP73838-FCI/MF

The MCP73837-NVI/MF is a linear Li-Ion/Li-Polymer battery charger controller from Microchip in a compact 10-pin DFN package. It features 1-channel charging with adjustable threshold, USB and AC adapter input management, and RoHS-compliant construction.

Microchip MCP6044-I/SL is a quad rail-to-rail operational amplifier operating from 1.6 V with 10 kHz gain-bandwidth product and 0.0001 µA typical bias current in a 14-pin SOIC package. It offers 80 dB typical CMRR and internal frequency compensation. From $0.80, in stock, worldwide shipping.

Microchip MCP73837-NVI/UN is a single-cell Li-Ion linear battery charger supporting dual USB and DC input sources, with 4.35 V charge termination and up to 1 A charge current, housed in a 10-pin MSOP package for compact portable device charging applications.

Microchip MCP6S22-I/SN is a 2-channel, 12 MHz programmable gain amplifier (PGA) with SPI interface, featuring selectable gains via software, operating from 2.5 V to 5.5 V supply, housed in SOIC-8 package for precision analog signal conditioning.

MCP6V07-E/SN is a dual auto-zero operational amplifier from Microchip with 130 dB minimum CMRR and 0.005 µA maximum average bias current in a standard 8-pin SOIC package. It delivers near-zero offset drift for precision DC and low-frequency measurement. Available from stock worldwide with fast shipping.

The MCP6V06-E/SN is a single auto-zero operational amplifier from Microchip. It delivers ultra-low offset voltage with 130 dB minimum CMRR and 0.005 µA maximum bias current in an SOIC-8 package. Available from stock worldwide with fast shipping.

The MCP73837-FCI/UN is a linear Li-Ion battery charger with dual USB and DC input sources, 4.2 V charge regulation, and up to 1 A charge current in a 10-pin MSOP package. It includes a power-good output, adjustable threshold, and automatic input source selection for portable device charging.

MCP6S26-I/SL is a 6-channel SPI-programmable gain amplifier (PGA) from Microchip with 12 MHz bandwidth, software-selectable gain, and single-supply operation. Packaged in a 14-pin SOIC for flexible analog front-end integration.

Microchip MCP73834-FCI/UN is a linear Li-Ion battery charge controller regulating to 4.2 V at up to 1 A charge current in a compact MSOP-10 package with thermal regulation. Available from stock with worldwide shipping.

MCP6L92T-E/SN is a dual 10 MHz CMOS operational amplifier from Microchip designed for extended temperature operation up to +125°C. It delivers 91 dB typical CMRR and a 4 mV maximum input offset voltage in an 8-pin SOIC package for cost-sensitive signal conditioning. Wide supply compatibility and internal frequency compensation simplify use in industrial and automotive analog designs.

MCP73837-FCI/MF is a single-cell lithium-ion and lithium-polymer linear battery charger controller with adjustable threshold in a compact 10-pin DFN package. From $1.20 in stock worldwide shipping.

MCP73213-B6SI/MF is a dual-cell lithium-ion battery charger with overvoltage protection from Microchip, featuring adjustable threshold, 2-channel input fault protection in a compact DFN-10 package with worldwide shipping.

The MCP6541T-E/OT is a single-channel push-pull output comparator from Microchip with rail-to-rail input/output operating from as low as 1.6 V. It features 5 nA maximum bias current and a 7 mV maximum input offset voltage in a tiny 5-pin SOT-23 package. Optimized for low-power threshold detection in battery-operated and IoT sensor applications.

The MCP6V02-E/SN is a dual-channel, auto-zero operational amplifier from Microchip delivering a 2 µV maximum input offset voltage and 142 dB typical CMRR. It operates from low supply voltages in an 8-pin SOIC package and is RoHS/Pb-free compliant.

Li-Ion Charge Controller 4.1V MSOP8

Microchip MCP3901A0-I/SS is a integrated circuit for embedded electronics, industrial controls, instrumentation, and production BOM sourcing. It offers 20 pins, -40°C to 85°C in Small Outline Packages. From quote-based sourcing, buyers can request stock checks and worldwide shipping support.