T1M-06-F-SV-L-K SAMTEC Connector (Other) In Stock
SAMTEC T1M-06-F-SV-L-K is a 6-position single-row vertical discrete wire terminal strip with 1.00 mm pitch and friction locking (-K) retention, spanning only 5 mm on the PCB for ultra-compact wire-to-board wiring. It is suited for fine-pitch signal harness connections in miniature electronic assemblies. Available from stock with worldwide shipping.
- Manufacturer
- SAMTEC
- Package
- Other
- Pin Count
- 6
- Lifecycle
- ACTIVE
- Datasheet
- T1M-06-F-SV-L-K Datasheet PDF
- Category
- Connector
- RoHS
- Compliant
- Lead Time
- 3–7 business days
- Shipping
- DHL Express · Worldwide
What are the key features of T1M-06-F-SV-L-K?
- 6-position single-row 1.00 mm pitch terminal strip spanning only 5 mm PCB footprint, enabling ultra-compact 6-wire discrete harness termination in miniature electronics
- Friction locking (-K) retention provides positive mating engagement without mechanical latches, simplifying field replacement while preventing accidental disconnection
- Vertical (SV) wire exit direction accommodates perpendicular cable routing to the PCB surface for minimal cable dress height in thin enclosures
What is T1M-06-F-SV-L-K used for?
T1M-06-F-SV-L-K is used in miniaturized electronic assemblies requiring 6 discrete signal wires at 1.00 mm pitch, such as wearable biosensors, micro-camera modules, and compact IoT sensor nodes. Its 5 mm footprint and friction-locking retention are well suited for consumer electronics and medical devices where easy cable service access is needed alongside secure in-use retention.
Compliance & Regulatory
| RoHS Status | Compliant |
| Lead-Free | Yes (Pb-Free) |
Where can I find the T1M-06-F-SV-L-K datasheet?
T1M-06-F-SV-L-K Datasheet DownloadOfficial datasheet from SAMTEC
What are equivalent replacements for T1M-06-F-SV-L-K?
Compatible alternatives and drop-in replacements for T1M-06-F-SV-L-K:
Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.039 inch Pitch, Surface Mount Terminal, Locking, Natural Insulator
Frequently Asked Questions
What is the PCB footprint of T1M-06-F-SV-L-K for a 6-position 1.00 mm pitch connector and why is it significant for miniature designs?
T1M-06-F-SV-L-K spans approximately 5 mm along the PCB edge for 6 positions at 1.00 mm pitch. Compared to a 6-position 2.54 mm pitch connector occupying 12.7 mm, this 60% footprint reduction allows placement in the narrow connector zones of wearable devices, earbuds, and micro-modules where PCB edge space is limited to under 10 mm per connector.
How does the friction locking (-K) retention of T1M-06-F-SV-L-K differ from the press-fit (-P) retention used on other T1M variants?
Friction locking (-K) relies on controlled interference fit between the mating housing and the terminal strip body, providing a tactile snap without a separate mechanical latch. This design allows tool-free insertion and extraction with moderate pull-out forces (typically 2 N to 5 N), whereas the press-fit (-P) variant locks more aggressively for higher-vibration environments. The -K variant is preferred in 6-pin service connectors that need frequent mating cycles.
For which signal types and current levels is T1M-06-F-SV-L-K rated?
The T1M series at 1.00 mm pitch is rated for signal applications carrying up to approximately 1.0 A per contact on fine-gauge 28 AWG to 32 AWG wires. T1M-06-F-SV-L-K is primarily used for low-current signal lines such as I2C, SPI, UART, or analog sensor outputs in the 0 V to 5 V range, where the 6-position connector handles up to 6 independent signal channels in a 5 mm footprint.
When should a designer choose T1M-06-F-SV-L-K over a 6-pin FPC connector at the same 1.00 mm pitch?
T1M-06-F-SV-L-K with discrete wires is preferred when cable routing requires individual wire flexibility, differing wire lengths, or shielded cables for each of the 6 channels, which flat FPC ribbons cannot provide. Discrete wire connectors also tolerate tighter bend radii in 3D cable assemblies and are easier to repair by re-crimping individual wires, making T1M-06-F-SV-L-K the better choice for service-friendly 6-channel 1.00 mm pitch interconnects.
Related Guides
CSD87313DMS Synchronous Buck Power Stage Design Guide
Design a compact CSD87313DMS synchronous buck stage with practical guidance for loss, gate drive, PCB layout, EMI, thermal validation, and sourcing.
Aug 6, 2026
STEF05SGR eFuse Selection Guide for 5 V Overcurrent Protection
Choose STEF05SGR for 5 V overcurrent protection by checking current-limit margin, inrush, thermal loss, fault response, and sourcing.
Aug 6, 2026
C0402C103K3RACTU Selection Guide: Choosing a 10 nF 0402 MLCC
Select C0402C103K3RACTU by voltage margin, X7R behavior, tolerance, 0402 assembly risk, and qualified alternatives.
Aug 4, 2026
STM32H753VIT6 MCU Selection Guide: Memory, Package, Connectivity, and Security
Choose STM32H753VIT6 by evaluating memory architecture, LQFP-100 pin fit, connectivity, security, power, and sourcing tradeoffs.
Aug 4, 2026
Why Buy from FindMyChip
About SAMTEC
SAMTEC is a leading electronic component manufacturer. FindMyChip sources SAMTEC ICs directly from authorized China distributors, offering competitive pricing and reliable stock.
In Stock · 24h Response · Worldwide Shipping
Response within 24 hours · Worldwide shipping
“Response time is incredible — usually under 4 hours. They understand that production lines can't wait.”
You May Also Like
10214-6212PC
3M
Connector
1778573
Phoenix Contact
Connector
5227222-3
TE Connectivity
Connector
S4B-XH-SM4-TB(LF)(SN)
JST (JAPAN SOLDERLESS TERMINALS)
Connector
185226-2
TE Connectivity
Connector
0533980571
Molex
Connector
0360-0-15-01-34-27-10-0
Mill-Max
Connector
7850-0006PR
3M
Connector
AVB 1,5/2/12
BLOCK
Connector
N3764-5002RB
3M
Connector
N3627-6002RB
3M
Connector
N3627-5002RB
3M
Connector
N3440-6002RB
3M
Connector
929715-03-36-I
3M
Connector
929667-02-36-I
3M
Connector
929665-04-36-I
3M
Connector
929665-02-36-I
3M
Connector
929647-04-36-I
3M
Connector
929647-03-36-I
3M
Connector
7834-0006PR
3M
Connector
7826-0006PR
3M
Connector
7820-0006PR
3M
Connector
3440-5002
3M
Connector
3433-5302
3M
Connector