SFM-149-T2-SM-D-A SAMTEC Connector (Other) In Stock
SAMTEC SFM-149-T2-SM-D-A is a 98-position, dual-row, high-reliability SMT socket strip at 0.050-inch (1.27mm) pitch for dense board-to-board interconnects. Gold-plated contacts and SMT termination enable reflow assembly with consistent signal integrity across all 98 positions. Stocked globally for prototype and high-volume production requirements.
- Manufacturer
- SAMTEC
- Package
- Other
- Pin Count
- 98
- Lifecycle
- ACTIVE
- Datasheet
- SFM-149-T2-SM-D-A Datasheet PDF
- Category
- Connector
- RoHS
- Compliant
- Lead Time
- 3–7 business days
- Shipping
- DHL Express · Worldwide
What are the key features of SFM-149-T2-SM-D-A?
- 98 positions in dual-row 0.050-inch (1.27mm) pitch for ultra-high-density board-to-board socket connections in mezzanine card assemblies
- High-reliability gold-plated contacts rated for 500+ mating cycles with stable contact resistance below 30mΩ
- Surface-mount termination (SM) compatible with standard reflow soldering at up to 260°C peak temperature
- T2 tail length and A-suffix contact style optimized for solder wetting and co-planarity on fine-pitch SMT PCB pads
What is SFM-149-T2-SM-D-A used for?
The SFM-149-T2-SM-D-A is used in high-pin-count mezzanine card assemblies, FPGA-to-processor carrier boards, and multi-chip module interfaces where 98 signal lines must pass between PCBs within a 1.27mm pitch constraint. Its 0.050-inch pitch and dual-row layout suit advanced telecom line cards, radar signal processor boards, and industrial motion controller daughtercards requiring dense parallel buses and differential signal pairs. The high-reliability gold contacts ensure signal integrity across vibration and thermal cycling in defense, aerospace, and test-and-measurement enclosures.
Compliance & Regulatory
| RoHS Status | Compliant |
| Lead-Free | Yes (Pb-Free) |
Where can I find the SFM-149-T2-SM-D-A datasheet?
SFM-149-T2-SM-D-A Datasheet DownloadOfficial datasheet from SAMTEC
What are equivalent replacements for SFM-149-T2-SM-D-A?
No known alternates. Submit an RFQ and our team can suggest alternatives.
Frequently Asked Questions
How does the 0.050-inch pitch of the SFM-149-T2-SM-D-A enable higher pin density than 0.100-inch alternatives on the same PCB edge?
At 1.27mm (0.050-inch) pitch, the SFM-149-T2-SM-D-A fits 98 positions in approximately 62mm of board length. An equivalent 0.100-inch pitch connector would require 124mm to accommodate the same 98 contacts, consuming twice the PCB edge space. This 50% length reduction is critical in 3U VPX and compact mezzanine card form factors where available connector zones are under 80mm.
For an FPGA development board with 96 user I/O signals, how does the SFM-149-T2-SM-D-A compare to using two 48-position connectors?
A single SFM-149-T2-SM-D-A with 98 positions handles all 96 FPGA I/O lines plus 2 power or ground pins in one connector, saving 1 connector footprint and eliminating the 2mm gap and skew mismatch between two 48-position strips. A single 98-position SMT connector at 1.27mm pitch also achieves tighter differential pair length matching, keeping skew under 10ps for multi-gigabit LVDS signals.
What is the mating cycle rating of the SFM-149-T2-SM-D-A and which use cases require this durability?
The SFM-149-T2-SM-D-A is rated for at least 500 mating cycles with gold-plated contacts maintaining under 30mΩ contact resistance throughout the rated life. This durability is required in test fixtures, lab breadboard prototypes, and field-replaceable line cards that are routinely unplugged and reseated during bring-up, debug, and periodic maintenance over a 5-10 year equipment service life.
What reflow profile is recommended for soldering the SFM-149-T2-SM-D-A's 98 SMT pads without connector warpage?
The SFM-149-T2-SM-D-A's surface-mount pads should be reflowed using a profile with a peak temperature of 245-260°C for no more than 30 seconds above 217°C per J-STD-020. Because the connector body spans approximately 62mm, a PCB warpage limit of 0.3mm over the connector length is critical to achieve simultaneous solder joint formation across all 98 positions without bridging or open joints at the row ends.
Related Guides
STM32H753VIT6 High-Performance MCU Design Guide
Practical STM32H753VIT6 design guidance for power, clocks, memory, DMA, PCB layout, bring-up, and production recovery.
Aug 3, 2026
STM32H753ZIT6 Selection Guide for High-Performance Embedded Systems
Select the STM32H753ZIT6 by evaluating compute, memory, LQFP144 pinout, power, interfaces, security, and sourcing requirements.
Aug 3, 2026
ICL7660ACPAZ Negative Voltage Charge Pump Design Guide
Design a reliable ICL7660ACPAZ negative rail with capacitor equations, layout rules, startup checks, and practical troubleshooting.
Aug 2, 2026
C0402C103K3RACTU 10 nF MLCC Design Guide
Practical guidance for applying the C0402C103K3RACTU 10 nF, 25 V X7R MLCC in decoupling, filtering, timing, and EMI-control networks.
Aug 2, 2026
Why Buy from FindMyChip
About SAMTEC
SAMTEC is a leading electronic component manufacturer. FindMyChip sources SAMTEC ICs directly from authorized China distributors, offering competitive pricing and reliable stock.
In Stock · 24h Response · Worldwide Shipping
Response within 24 hours · Worldwide shipping
“Their engineering team helped us find a pin-compatible alternative when our original MCU went EOL.”
You May Also Like
10214-6212PC
3M
Connector
1778573
Phoenix Contact
Connector
5227222-3
TE Connectivity
Connector
S4B-XH-SM4-TB(LF)(SN)
JST (JAPAN SOLDERLESS TERMINALS)
Connector
185226-2
TE Connectivity
Connector
0533980571
Molex
Connector
0360-0-15-01-34-27-10-0
Mill-Max
Connector
7850-0006PR
3M
Connector
AVB 1,5/2/12
BLOCK
Connector
N3764-5002RB
3M
Connector
N3627-6002RB
3M
Connector
N3627-5002RB
3M
Connector
N3440-6002RB
3M
Connector
929715-03-36-I
3M
Connector
929667-02-36-I
3M
Connector
929665-04-36-I
3M
Connector
929665-02-36-I
3M
Connector
929647-04-36-I
3M
Connector
929647-03-36-I
3M
Connector
7834-0006PR
3M
Connector
7826-0006PR
3M
Connector
7820-0006PR
3M
Connector
3440-5002
3M
Connector
3433-5302
3M
Connector