MCP4632-104E/UN Microchip Integrated Circuit (Small Outline Packages) In Stock

Microchip MCP4632-104E/UN is a dual-channel digital potentiometer with 128 steps and 100 kOhm end-to-end resistance, controlled via I2C 2-wire serial interface, housed in an MSOP-10 package. Available from global distributors with worldwide shipping.

ACTIVEIntegrated CircuitVerified Jun 2026
Package / Visual Reference
MCP4632-104E/UNSmall Outline Packages
Quick Facts
Manufacturer
Microchip
Package
Small Outline Packages
Pin Count
10
Lifecycle
ACTIVE
Category
Integrated Circuit
Price
From $0.7930(MOQ 1)
Temp Range
-40.0°C to 125.0°C
RoHS
Compliant
Lead Time
3–7 business days
Shipping
DHL Express · Worldwide

Key Features

  • 128-step resolution digital potentiometer providing fine-grained resistance adjustment from 0 to 100 kOhm in software
  • I2C 2-wire serial control interface allowing daisy-chain configuration with multiple devices on a single bus
  • Dual-channel design in a compact MSOP-10 package, replacing two mechanical potentiometers in one IC
  • Non-volatile wiper position storage retaining the last programmed setting through power cycles without a microcontroller

Applications

The MCP4632-104E/UN serves as a software-configurable resistance element in audio volume control circuits, LCD display contrast adjustment, and analog signal gain tuning stages. Its I2C interface allows a host microcontroller to adjust both channels independently over a 2-wire bus shared with other peripherals, reducing GPIO usage. The 100 kOhm full-scale resistance and 128-step resolution make it a direct digital replacement for manual preset potentiometers in calibration and trimming applications.

Specifications

Manufacturer Package CodeMSOP-10
Factory Lead Time4Weeks
YTEOL9
Additional FeatureTHE RESISTOR ARRAY VALUES ARE 5000 OHM,10000 OHM, 50000 OHM
Bandwidth-Nom2kHz
Control Interface2-WIRE SERIAL
Converter TypeDIGITAL POTENTIOMETER
JESD-30 CodeS-PDSO-G10
JESD-609 Codee3
Number of Functions1
Number of Positions257
Package Body MaterialPLASTIC/EPOXY
Package Equivalence CodeTSSOP10,.19,20
Package ShapeSQUARE
Package StyleSMALL OUTLINE
Peak Reflow Temperature (Cel)260
Qualification StatusNot Qualified
Resistance LawLINEAR
Resistance Tolerance-Max20%
Resistor Terminal Voltage-Max5.5V
Screening LevelTS 16949
Supply Current-Max0.6mA
Supply Voltage-Nom3V
Surface MountYES
TechnologyCMOS
Temperature Coefficient-Nom150ppm/°C
Temperature GradeAUTOMOTIVE
Terminal FinishMatte Tin (Sn)
Terminal FormGULL WING
Terminal Pitch0.5mm
Terminal PositionDUAL
Time@Peak Reflow Temperature-Max (s)40
Total Resistance-Nom100000Ω
PackageSmall Outline Packages

Compliance & Regulatory

RoHS StatusCompliant
Lead-FreeYes (Pb-Free)
Moisture Sensitivity LevelMSL 2
HTS Code8542.39.00.60
Country of OriginThailand

Datasheet

MCP4632-104E/UN Datasheet Download

Official datasheet from Microchip

Alternate & Equivalent Parts

No known alternates. Submit an RFQ and our team can suggest alternatives.

Frequently Asked Questions

How many resistance steps does the MCP4632-104E/UN provide and what is its step size?

The MCP4632-104E/UN offers 128 wiper positions across a 100 kOhm end-to-end resistance, giving a nominal step size of approximately 781 ohms per step. This resolution is sufficient for audio taper volume control, sensor bias trimming, and gain-setting resistor dividers where mechanical potentiometers previously required manual calibration.

For an LCD display brightness control design, how does the I2C interface of MCP4632-104E/UN reduce board complexity?

The MCP4632-104E/UN uses a 2-wire I2C serial interface, allowing it to share the SCL/SDA bus with other I2C peripherals such as temperature sensors and EEPROM chips. This eliminates 2 dedicated GPIO lines compared to SPI-based alternatives, and the dual-channel design controls 2 independent backlight or contrast circuits from one MSOP-10 package, cutting component count.

When should a designer use MCP4632-104E/UN instead of a fixed resistor or a mechanical trimmer?

MCP4632-104E/UN is preferred when the required resistance must be adjusted in the field by firmware without physical access to the PCB, such as in sealed industrial enclosures. The 128-step digital control over 100 kOhm range with I2C commands replaces a manual trimmer, enables automated factory calibration routines at 2 kHz bandwidth, and maintains the set value in non-volatile memory after power-down.

What end-to-end resistance options does Microchip offer in the MCP4632 family beyond the 100 kOhm variant?

Within the MCP4632 family, Microchip offers 5 kOhm and 50 kOhm end-to-end resistance variants in addition to the 100 kOhm MCP4632-104E/UN. All share the same 128-step resolution, I2C interface, and MSOP-10 package, so swapping resistor values requires only a part number change and adjusted software scaling without PCB layout changes.

Why Buy from FindMyChip

Authorized Source
Verified supply chain with full traceability & inspection
$
Competitive Pricing
Factory-direct from China distributors, low MOQ
Fast Shipping
DHL Express 3–5 days · FedEx/UPS 5–7 days worldwide
Quality Guaranteed
30-day replacement for defective parts, no questions asked

About Microchip

Microchip is a leading electronic component manufacturer. FindMyChip sources Microchip ICs directly from authorized China distributors, offering competitive pricing and reliable stock.

AvailabilityIn Stock
Reference Price (USD)
From $0.7930
Buy from 1pc · Factory-direct pricing
Qty.Unit PriceExt. Price
1+$1.2000$1.20
100+$0.8900$89.00
1000+$0.8700$870.00
5000+$0.8000$4000.00
7500+$0.7980$5985.00
10000+$0.7930$7930.00
pcs
Unit price: $1.2000 · Total: $1.20

In Stock · 24h Response · Worldwide Shipping

Lead Time3-7 business days
MOQFrom 1 piece
ShippingDHL / FedEx / UPS
OriginChina (Authorized)

Response within 24 hours · Worldwide shipping

We've been using FindMyChip for 2 years. Pricing is consistently 20-30% below Mouser/DigiKey for volume orders.

SK
Sarah Kim
VP Engineering, NovaBit Electronics, South Korea