MCP4532-103E/MS Microchip Integrated Circuit (Small Outline Packages) In Stock

The MCP4532-103E/MS is a single-channel 10 kΩ digital potentiometer with 129-position linear resolution and I2C 2-wire interface in an 8-pin MSOP package. It offers non-volatile wiper position storage and 2 kHz bandwidth for analog signal control and calibration applications.

ACTIVEIntegrated CircuitVerified May 2026
Package / Visual Reference
MCP4532-103E/MSSmall Outline Packages
Quick Facts
Manufacturer
Microchip
Package
Small Outline Packages
Pin Count
8
Lifecycle
ACTIVE
Category
Integrated Circuit
Temp Range
-40.0°C to 125.0°C
RoHS
Compliant
Lead Time
3–7 business days
Shipping
DHL Express · Worldwide

Key Features

  • 129-position linear taper with 10 kΩ end-to-end resistance and 2 kHz -3 dB bandwidth for precision voltage division and signal attenuation
  • I2C 2-wire serial interface with hardware address pins allows up to 8 devices on a single bus, minimizing wiring in multichannel designs
  • Non-volatile wiper memory retains position through power cycles, eliminating startup initialization routines in calibration and gain-setting applications

Applications

The MCP4532-103E/MS serves as a programmable gain element or DC bias adjustment in analog front-end circuits for sensors, audio processing, and measurement equipment. Its I2C interface and 129-step resolution enable fine-grained software-controlled calibration of amplifier gain, filter cutoff, and reference voltage trimming without mechanical adjustments. Medical instrumentation and industrial transmitters benefit from its non-volatile wiper memory, ensuring consistent analog output after power cycling.

Specifications

Manufacturer Package CodeMSOP-8
Factory Lead Time11Weeks
YTEOL9
Additional FeatureTHE RESISTOR ARRAY VALUES ARE 5000 OHM,10000 OHM, 50000 OHM
Bandwidth-Nom2kHz
Control Interface2-WIRE SERIAL
Converter TypeDIGITAL POTENTIOMETER
JESD-30 CodeS-PDSO-G8
JESD-609 Codee3
Number of Functions1
Number of Positions257
Package Body MaterialPLASTIC/EPOXY
Package Equivalence CodeSOP8,.19
Package ShapeSQUARE
Package StyleSMALL OUTLINE
Peak Reflow Temperature (Cel)260
Qualification StatusNot Qualified
Resistance LawLINEAR
Resistance Tolerance-Max20%
Resistor Terminal Voltage-Max5.5V
Screening LevelTS 16949
Supply Current-Max0.6mA
Supply Voltage-Nom3V
Surface MountYES
TechnologyCMOS
Temperature Coefficient-Nom150ppm/°C
Temperature GradeAUTOMOTIVE
Terminal FinishMatte Tin (Sn)
Terminal FormGULL WING
Terminal Pitch0.65mm
Terminal PositionDUAL
Time@Peak Reflow Temperature-Max (s)40
Total Resistance-Nom100000Ω
PackageSmall Outline Packages

Compliance & Regulatory

RoHS StatusCompliant
Lead-FreeYes (Pb-Free)
Moisture Sensitivity LevelMSL 1
ECCNEAR99
HTS Code8542.39.00.01
Country of OriginThailand

Datasheet

MCP4532-103E/MS Datasheet Download

Official datasheet from Microchip

Alternate & Equivalent Parts

No known alternates. Submit an RFQ and our team can suggest alternatives.

Frequently Asked Questions

How many discrete resistance steps does the MCP4532-103E/MS offer and what is the step size for a 10 kΩ device?

The MCP4532-103E/MS provides 129 wiper positions across a 10 kΩ end-to-end resistance, giving a resolution of approximately 78 Ω per step. This fine granularity supports precision gain trimming and DC offset correction in 12-bit and 16-bit ADC front-end circuits where coarser 32-position or 64-position potentiometers introduce excessive quantization error.

How does the I2C address selection on the MCP4532-103E/MS enable multi-device configurations on the same bus?

The MCP4532-103E/MS uses 2 hardware address pins to set one of 4 unique I2C device addresses, allowing up to 4 devices to share a single 2-wire I2C bus. Combining MCP4532 variants with different address configurations extends this to 8 devices on one bus, supporting multichannel gain or attenuation control in audio mixers and sensor arrays with only 2 signal wires and no SPI chip-select lines.

For an industrial sensor calibration board, what advantages does the MCP4532-103E/MS non-volatile memory provide compared to a volatile digital potentiometer?

The non-volatile wiper memory retains the last programmed position across power cycles without a backup battery or external EEPROM. In a factory calibration workflow, the trimming value is written once at end-of-line test and stored permanently, so the sensor node boots with the correct 10 kΩ wiper setting on each power-up. Volatile alternatives require MCU firmware to reload calibration from external storage on every power cycle, adding firmware complexity and potential failure modes.

Related Guides

Why Buy from FindMyChip

Authorized Source
Verified supply chain with full traceability & inspection
$
Competitive Pricing
Factory-direct from China distributors, low MOQ
Fast Shipping
DHL Express 3–5 days · FedEx/UPS 5–7 days worldwide
Quality Guaranteed
30-day replacement for defective parts, no questions asked

About Microchip

Microchip is a leading electronic component manufacturer. FindMyChip sources Microchip ICs directly from authorized China distributors, offering competitive pricing and reliable stock.

AvailabilityIn Stock
Reference Price (USD)
Contact for Price
Buy from 1pc · Factory-direct pricing
pcs

In Stock · 24h Response · Worldwide Shipping

Lead Time3-7 business days
MOQFrom 1 piece
ShippingDHL / FedEx / UPS
OriginChina (Authorized)

Response within 24 hours · Worldwide shipping

We've been using FindMyChip for 2 years. Pricing is consistently 20-30% below Mouser/DigiKey for volume orders.

SK
Sarah Kim
VP Engineering, NovaBit Electronics, South Korea